Chorus - Home Automation
KNX Easy BUS

CHARACTERISTICS: integrated coil to uncouple the power supply from the BUS line.
Reset push-button for restoring all the devices connected to the BUS line.
APPLICATIONS: the power supply feeds and controls the BUS voltage.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).
The maximum number of devices that can be powered is calculated on the basis of their absorption.

APPLICATIONS: to be used as a repeater in a KNX Easy system, when you want to create an architecture containing more than one line segment.
NOTES: equipped with 2 coupling terminals for connection to BUS.

CHARACTERISTICS: equipped with B-type USB port.
APPLICATIONS: for the connection of a PC with a USB port to the KNX BUS.
NOTES: equipped with coupling terminal for connection to bus.

CHARACTERISTICS: equipped with A-type USB connector.
APPLICATIONS: for the connection of a PC with a USB port to the KNX BUS.
NOTES: equipped with A-type USB 2.0 extension, male-female (length 15 cm) and screw terminal for connection to the bus.
AVAILABILITY: item available while stocks last.

CHARACTERISTICS: equipped with RJ45 port.
APPLICATIONS: for connecting a PC via LAN to the KNX BUS. Supports up to 5 simultaneous connections. To be used with the HAPPY HOME app for smartphones and tablets (available for Android and iOS) to manage the KNX domotic system via LAN and WiFi access points, or from a distance. The app can also be used with the codes GW90767 and GW90767AP.
NOTES: equipped with coupling terminal for connection to bus.

CHARACTERISTICS: equipped with A-type USB connector.
APPLICATIONS: for the connection of a PC with a USB port to the KNX BUS.
NOTES: equipped with screw terminal for connection to the bus.
AVAILABILITY: item available when GW90706S is out of stock.

CHARACTERISTICS: Easy module with 6 independent channels. Each channel is associated with an RGB night-time backlit LED or a status display LED for the commanded load. Each channel can be personalised using a set of adhesive icons. To be completed with the glass ICE Touch KNX plate (code GW16946CB, GW16946CN, GW16946CT). The device's touch commands can only be activated with the plate mounted: therefore, to configure the module the ICE Touch KNX plates or alternative the test plate (GW16950) must be used. To be configured with ETS software or with Easy Controller.
APPLICATIONS: used for sending ON-OFF commands with fronts management, switching commands, timed commands, priority commands, commands for managing roller shutters (single or double push-button), dimmers (single or double push-button) and scenes (storage and activation).
NOTES: equipped with coupling terminal with protection lid, for connection to BUS, and with set of icons to personalise the functions of each channel.

CHARACTERISTICS: plates made in glass with a glossy finish, used to complete the touch push-button panel modules - KNX (GWA9421) or Easy (GWA9471). The plates have 6 capacitive touch areas.
NOTES: the symbols shown in the picture are indicative only: they can be personalised using the set of adhesive icons included in the touch push-button module package. The code of the plate is unique and independent from the number of channels that you want to activate (from 1 to 6).

CHARACTERISTICS: plates made in glass with a glossy finish, used to complete the touch push-button panel modules - KNX (GWA9421) or Easy (GWA9471). The plates have 6 capacitive touch areas.
NOTES: the symbols shown in the picture are indicative only: they can be personalised using the set of adhesive icons included in the touch push-button module package. The code of the plate is unique and independent from the number of channels that you want to activate (from 1 to 6).

CHARACTERISTICS: plates made in glass with a glossy finish, used to complete the touch push-button panel modules - KNX (GWA9421) or Easy (GWA9471). The plates have 6 capacitive touch areas.
NOTES: the symbols shown in the picture are indicative only: they can be personalised using the set of adhesive icons included in the touch push-button module package. The code of the plate is unique and independent from the number of channels that you want to activate (from 1 to 6).

CHARACTERISTICS: plate in transparent plastic, with 6 capacitive touch areas.
NOTES: to be used for configuring the touch push-button panel modules - KNX (GWA9421) or Easy (GWA9471) - if the ICE touch KNX glass plates are not available in the system.

CHARACTERISTICS: Easy module with 6 independent channels, with touch commands (capacitive) and temperature sensor. Each channel is associated with an amber/blue LED for night-time backlit or to show the status of the commanded load. To be completed with italian standard ICE Touch KNX glass plate (code GW16962CB, GW16964CB, GW16966CB, GW16962CN, GW16964CN, GW16966CN, GW16962CT, GW16964CT, GW16966CT). To be configured with ETS software or with Easy Controller.
APPLICATIONS: allows you to send ON-OFF commands with fronts management, switchover commands, timed commands, commands for managing roller shutters (single or double push-button), dimmers (single or double push-button) and scenes (memorisation and activation).
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: plates in glass and with a glossy finish, used to complete the touch push-button panel modules - KNX (GW10746) or Easy (GW10741).

CHARACTERISTICS: plates in glass and with a glossy finish, used to complete the touch push-button panel modules - KNX (GW10746) or Easy (GW10741).

CHARACTERISTICS: plates in glass and with a glossy finish, used to complete the touch push-button panel modules - KNX (GW10746) or Easy (GW10741).

CHARACTERISTICS: BUS interfaces for connecting 2 or 4 push-buttons or conventional potential-free contacts. The reading voltage (SELV) is generated inside the device. For each input, an output is available for powering a low absorption LED (lower than 1mA such as, for example, GW10886, GW10887, GW10888, GW10889, GW10890) for displaying the status of the load commanded. To be configured with ETS software or with Easy Controller.
APPLICATIONS: for sending ON-OFF commands with fronts management, switching commands, timed commands, priority commands, commands for controlling thermoregulation and commands for managing roller shutters (single or double push-button), dimmers (single or double push-button), scenes (storage and activation), output LED control, acquisition of temperature values via NTC sensor (GW90834A only). The input channels can be configured as alarm inputs (weather sensors). Installation in flush-mounting box, junction boxes or embedded in the blanking modules GW10571, GW12571, GW14571. The slot on the plastic casing also allows it to be fixed with screws.
NOTES: equipped with coupling terminal for connection to the BUS, and unshielded cables for connecting the inputs, of length 30 cm extendible to 10m with unshielded twisted cable.

NOTES: the miniature lamps are equipped with power cables.
If connected with the interfaces GW90721, GW90834, GW90721A, GW90727, GW90834A, GW90833 they do not require the use of a current limiting resistance. In this case, the maximum current consumption is less than 1mA.

CHARACTERISTICS: 1-gang blanking module with pad printing KNX/EIB.
Allows the housing and fast identification of the 2- and 4-channel contact interface.
NOTES: embedded coupling.

CHARACTERISTICS: Easy module with 6 independent channels, with replaceable button keys and built-in temperature sensor. Each channel is associated with an amber/green night-time locating LED or a status display LED for the commanded load. To be configured with ETS software or with Easy Controller. The package includes 3 replaceable button keys (GW1x553) and 10 lenses with illuminated symbols (2 x GW10502A, 1 x GW10509A, 1 x GW10510A, 1 x GW10513A, 1 x GW10514A, 1 x GW10519A, 1 x GW10520A, 1 x GW10529A, 1 x GW10530A). You can still customize the module with other type of replaceable button keys (suited for 1 or 2 lenses, with 2 diffusers, 1- or 2-module) or with other lenses in the catalogue.
APPLICATIONS: allows you to send ON-OFF commands with fronts management, switchover commands, timed commands, commands for roller shutter management (single or double push-button), dimmers (single or double push-button) and scenes (memorisation and activation).
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: Easy module with 6 independent channels, with replaceable button keys and 1-channel ON/OFF actuator. Each channel is associated with an amber/green night-time locating LED or a status display LED for the commanded load. One pair of keys can be used for local actuator command. The actuator manages the load via a potential-free output contact (NO). To be configured with ETS software or with Easy Controller. The package includes 3 replaceable button keys (GW1x553) and 10 lenses with illuminated symbols (2 x GW10502A, 1 x GW10509A, 1 x GW10510A, 1 x GW10513A, 1 x GW10514A, 1 x GW10519A, 1 x GW10520A, 1 x GW10529A, 1 x GW10530A). You can still customize the module with other type of replaceable button keys (suited for 1 or 2 lenses, with 2 diffusers, 1- or 2-module) or with other lenses in the catalogue.
APPLICATIONS: the push-button panel allows to send ON-OFF commands with fronts management, switchover commands, timed commands, commands for roller shutter management (single or double push-button), dimmers (single or double push-button) and scenes (memorisation and activation). The actuator allows the execution of ON-OFF commands, timed commands with pre-alarm at switch-off, priority commands and scene management commands. For discharge lamps and compensated fluorescent lamps, use a support relay.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: Easy module with 6 independent channels, with replaceable button keys and 1-channel roller shutter actuator. Each channel is associated with an amber/green night-time locating LED or a status display LED for the commanded load. One pair of keys can be used for local actuator command. The actuator manages a motor to move roller-shutters, curtains, venetian blinds, rolling blinds, etc. via 2 potential-free interlocked output contacts (NO). To be configured with ETS software or with Easy Controller. The package includes 3 replaceable button keys (GW1x553) and 10 lenses with illuminated symbols (2 x GW10502A, 1 x GW10509A, 1 x GW10510A, 1 x GW10513A, 1 x GW10514A, 1 x GW10519A, 1 x GW10520A, 1 x GW10529A, 1 x GW10530A). You can still customize the module with other type of replaceable button keys (suited for 1 or 2 lenses, with 2 diffusers, 1- or 2-module) or with other lens in the catalogue.
APPLICATIONS: the push-button panel allows to send ON-OFF commands with fronts management, switchover commands, timed commands, commands for roller shutter management (single or double push-button), dimmers (single or double push-button) and scenes (memorisation and activation). The actuator allows the execution of commands of movements/adjustment/stopping, along with priority commands, scene management and alarm signalling commands.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: Easy module with 4 independent channels, with replaceable button keys. Each channel is associated with a RGB LED for night-time locating or status display for the commanded load. To be configured with ETS software or with Easy Controller. The package includes 2 replaceable button keys (GW1x553) and 10 lenses with illuminated symbols (2 x GW10502A, 1 x GW10509A, 1 x GW10510A, 1 x GW10513A, 1 x GW10514A, 1 x GW10519A, 1 x GW10520A, 1 x GW10529A, 1 x GW10530A). You can still customize the module with other type of replaceable button keys (arranged for 1 or 2 lenses, with 2 diffusers, 1 or 2 modules) or with other lenses in the catalogue.
APPLICATIONS: allows you to send ON-OFF commands with fronts management, switchover commands, timed commands, commands for roller shutter management (single or double push-button), dimmers (single or double push-button) and scenes (memorisation and activation).
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

NOTES: to be used for the customization of Easy (GW1x753A, GW1x754A, GW1x755A, GW1x757) and KNX (GW1x783A, GW1x784A, GW1x785A, GW1x787) 6 and 4-channel push-button panels with interchangeable symbols.

CHARACTERISTICS: with "Do not disturb" and "Make up the room" pad printings. Include lenses with illuminated symbols.
NOTES: to be used for the customization of Easy (GW1x753A, GW1x754A, GW1x755A, GW1x757) and KNX (GW1x783A, GW1x784A, GW1x785A, GW1x787) 6- and 4-channel push-button panels with interchangeable symbols.

NOTES: to be used for the customization of the button keys of Easy (GW1x753A, GW1x754A, GW1x755A, GW1x757) and KNX (GW1x783A, GW1x784A, GW1x785A, GW1x787) 6 and 4-channel push-button panels with interchangeable symbols.

CHARACTERISTICS: push-button panel with 4 button keys/4 channels. Each button key is associated with an amber LED for night-time backlit, and a green LED to display the status of the commanded load. To be configured with ETS software or with Easy Controller.
APPLICATIONS: allows you to send ON-OFF commands with fronts management, switchover commands, timed commands, commands for roller shutter management (single or double push-button), dimmers (single or double push-button) and scenes (memorisation and activation).
NOTES: equipped with coupling terminal with protection lid, for connection to BUS, and with set of icons to personalise the button key functions.

CHARACTERISTICS: push-button suitable for connection of KNX BUS contacts interfaces, or the command of bistable relays, electronic one-way switches for heavy duty loads, or dimmers with a remote control input. Output contact 4A (AC1) - 230 V ac.

CHARACTERISTICS: push-button for BUS inputs, suitable for KNX BUS contact interface connections. Equipped with 2-colour (amber/green) LED with colour selector (can be set up to work as a night-time localisation lamp or to indicate the load status).

CHARACTERISTICS: double push-button suitable for connecting KNX BUS contact interfaces or electronic control panels for moving roller shutters.

CHARACTERISTICS: movement sensor with detection conditioned by the light threshold value set. Adjustable lens. Operating range: 10m.
Vertical bearing angle: 30°. Horizontal bearing angle: 105°. Light threshold value can be adjusted via the front access trimmer.
The cycle time can be set in pre-fixed steps via the Easy controller (10s...5min), and can be modified (± 50%) via the front access trimmer.
Front green LED signals movement detection and command entry.
To be configured with ETS software or with Easy Controller.
APPLICATIONS: allows you to send timed commands to the movement detector. The entry of commands may be conditioned by the status of the controlled actuator.
The device is able to manage a safety pause of 5 seconds upon the deactivation of the controlled load. For installation indoors.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: anemometer to be used in combination with the wind sensor interface GW90770.

CHARACTERISTICS: allows the GW90769 wind sensor to be interfaced with a contacts interface.
Generates an alarm signal via a potential-free, NO contact, on the basis of the wind intensity (adjustable with 10 threshold values, 3.3...24.5m/s). Wall-mounting.

CHARACTERISTICS: 1-channel actuator for activating loads via a potential-free output contact (NO/NC).
Equipped with a front push-button for local command and a indicator LED for output contact closure. To be configured with ETS software or with Easy Controller.
APPLICATIONS: execution of ON-OFF commands, timed commands with pre-alarm at switch-off, priority commands, and scene management commands.
For discharge lamps and compensated fluorescent lamps, use a support relay.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid). If there is a failure in the BUS voltage, the output contact will remain open when the voltage is restored.

CHARACTERISTICS: 4-channel actuator for activating loads via potential-free output contacts (NO). Suitable for commanding incandescent lamps (230 V ac): 1500 W, halogen lamps (230 V ac): 1500 W, loads controlled from electronic transformers: 600 VA, uncompensated fluorescent lamps: 400 VA, energy saving lamps (compact fluorescent): 8x23 W. Max switchover current 10 A (cos.fi 1). Use a support relay for the compensated fluorescent lamps and for all loads that are not indicated.
Equipped with front push-buttons for local implementation, and signalling LED for closure of output contact. To be configured with ETS software or with Easy Controller.
APPLICATIONS: execution of ON-OFF commands, timed commands with pre-alarm at switch-off, priority commands, and scene management commands.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: 4-channel actuator for activating loads via potential-free output contacts (NO).
Suitable for commanding incandescent lamps (230 V ac): 3000 W, halogen lamps (230 V ac): 3000 W, loads controlled from toroidal transformers: 3000 W, loads controlled from electronic transformers: 2000 W, energy saving lamps (compact fluorescent): 80x23 W.
Max switchover current 16A (AC1), 16AX (140µF ref EN 60669-1) fluorescent loads with maximum surge current 400A (200µs).
Equipped with front push-buttons for local implementation, and signalling LED for closure of output contact. To be configured with ETS software or with Easy Controller.
APPLICATIONS: execution of ON-OFF commands, timed commands with pre-alarm at switch-off, priority commands, and scene management commands.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: 1-channel actuator to activate a motor to move roller-shutters, curtains, Venetian blinds, rolling blinds, etc. via 2 potential-free interlocked output contacts (NO). With two frontal push-buttons for local activation, and two LEDs indicating output contact closure. To be configured with ETS software or with Easy Controller.
APPLICATIONS: carries out commands of movement/adjustment/stopping, along with priority commands, scene management and alarm signalling commands.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid). If there is a failure in the BUS voltage, the roller shutter or Venetian blind will remain immobile when the voltage is restored, until a new movement command is given.

CHARACTERISTICS: 2- and 4-channel actuators to activate motors to move roller-shutters, curtains, venetian blinds, rolling blinds, etc. via respectively 4 and 8 potential-free interlocked output contacts (NO). With 4 (8) frontal push-buttons for local activation, and 4 (8) LEDs indicating output contact closure. To be configured with ETS software or with Easy Controller.
APPLICATIONS: carries out commands of movement/adjustment/stopping, along with priority commands, scene management and alarm signalling commands.
NOTES: equipped with coupling terminal with protection lid, for connection to BUS. If there is a failure in the BUS voltage, the roller shutter or Venetian blind will remain immobile when the voltage is restored, until a new movement command is given.
GW90852: Possibility to activate the loads manually, even without the BUS voltage.

CHARACTERISTICS: for the adjustment and switching of incandescent and halogen lamps 230V AC, low voltage halogen lamps with electronic and winding transformers, LED lamps 230V AC with dimmer function, and CFL lamps with dimmer function. Manual selection of the type of load (Leading Edge or Trailing Edge piloting), soft-start function for lamp protection, front LEDs for signalling the status of the outputs. To be configured with ETS software or with Easy Controller.
APPLICATIONS: execution of ON-OFF commands, relative and absolute light intensity adjustment, scene management, timed commands, priority commands, sending of channel status and light intensity signals.
NOTES: equipped with a coupling terminal for connection to the BUS, with a protection lid. In the event of a BUS failure, the device maintains the output status. The behaviour when the BUS voltage is restored can be freely configured.

CHARACTERISTICS: bleeder for dimmable LED lamps. Supplied with cables (length 15cm).
APPLICATIONS: suitable for Easy (GWA9351, GWA9352), KNX (GWA9301, GWA9302) or traditional (GW1x572, GW1x573) universal dimmers.

CHARACTERISTICS: dimmer in CVD version (control with constant voltage) for regulating RGB(W) LED strips, and in CCD version (control with constant current) for regulating "power" LEDs. 4 front button keys for testing the outputs and 4 front LEDs for signalling the load status and other operating parameters. To be configured with ETS software or with Easy Controller.
APPLICATIONS: execution of ON-OFF commands, regulation and setting of the light intensity level for each single channel (and the 4 channels simultaneously), selection of feedback on status or light intensity value, scene management, timed sequences, priority commands, logic functions. The 4 outputs can be used to control each of the 4 channels R, G, B and W of a single LED lamp, or up to 4 independent LEDs.
NOTES: equipped with a coupling terminal for connection to the BUS, with a protection lid. In the event of a BUS voltage failure or a failure on the auxiliary power supply voltage to the LEDs, the device brings all the channels to OFF (0%). The behaviour when the BUS voltage is restored can be freely configured; when the auxiliary voltage is restored, the dimmer implements the last command received.

CHARACTERISTICS: device used to extend the control capacity of CVD LED dimmers by up to 10A per channel.
APPLICATIONS: to be used with KNX (GW90764) and Easy (GW90854) dimmer actuators for CVD LEDs.
NOTES: equipped with coupling terminal for connection to BUS (with protection lid).

CHARACTERISTICS: flush-mounting timed thermostat with humidity management, that can be programmed on a weekly basis to control heating/cooling and humidification/dehumidification systems on the BUS. 3-level temperature profile (comfort, pre-comfort, economy). Control algorithms for 2- or 4-way systems: two points (ON/OFF), proportional-integral (PWM), fan coil (3 speeds). Includes: 1 output for commanding the area solenoid valve, 1 input for a potential free contact (window contact function), 1 input for the external temperature NTC probe sensor (e.g.: protection for floor-mounting heating). With 7 hour profiles that can be freely used (programmer function) plus another two reserved for the timed thermostat, with 15-minute resolution. Equipped with an extractable front and LCD display with customisable RGB backlighting. To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with Easy flush-mounting thermostats for local temperature adjustment: In this case, the timed thermostat acts as a master, sending the temperature profile to the BUS.
NOTES: equipped with coupling terminal for connection to BUS. The device requires a back-up power supply from 2 AA alkaline batteries (not included), housed in the extractable front, to guarantee the updating of the calendar (day, time) in the event of a BUS voltage failure. The device does not have a built-in humidity sensor, so the relative humidity value must be obtained from an external KNX sensor (e.g. GW1x762H).

CHARACTERISTICS: flush-mounting thermostat with humidity management, to control heating/cooling and humidification/dehumidification systems on the BUS and to manually manage the temperature on three levels (comfort, pre-comfort, economy). Control algorithms for 2- or 4-way systems: two points (ON/OFF), proportional-integral (PWM), fan coil (3 speeds). Includes: 1 output for commanding the area solenoid valve, 1 input for a potential-free contact (window contact function), 1 input for the external temperature NTC probe sensor (e.g. protection for floor-mounting heating). Equipped with an LCD display with customisable RGB backlighting. To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with Easy flush-mounting timed thermostats for local temperature adjustment: in this case, the thermostat acts as a Slave, executing the temperature profile sent from the Master (timed thermostat), using the locally defined setpoint values. If the system contains remote elements with their own control logic (e.g. Easy flush-mounting temperature adjustment probes), the thermostat can be used to visualise and set their operating parameters (max. 4 elements).
NOTES: equipped with coupling terminal for connection to BUS. The device does not have a built-in humidity sensor, so the relative humidity value must be obtained from an external KNX sensor (e.g. GW1x762H).

CHARACTERISTICS: flush-mounting temperature adjustment probe for controlling heating/cooling systems on the BUS. 3-level temperature profile (comfort, pre-comfort, economy). Control algorithms for 2- or 4-way systems: two points (ON/OFF), proportional-integral (PWM), fan coil (3 speeds). Includes: 1 input for a potential free contact (window contact function), 1 input for external temperature NTC sensor (e.g. protection for floor-mounting heating). Equipped with a front LED signalling the operating status and the load status (solenoid valve). To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with thermostats GW10765H, GW12765H, GW14765H or timed thermostats GW10764H, GW12764H, GW14764H to adjust the temperature in specific areas and for controlling and displaying the probe parameters (the probe does not have a display).
NOTES: it is equipped with coupling terminal for connection to bus.

CHARACTERISTICS: flush-mounting temperature adjustment probe with humidity sensor for controlling heating/cooling systems and humidification/dehumidification systems on the BUS. 3-level temperature profile (comfort, pre-comfort, economy). Control algorithms for 2- or 4-way systems: two points (ON/OFF), proportional-integral (PWM), fan coil (3 speeds). Includes: 1 input for a potential free contact (window contact function), 1 input for external temperature NTC sensor (e.g. protection for floor-mounting heating). Equipped with a front LED signalling the operating status and the load status (solenoid valve). To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with thermostats GW10765H, GW12765H, GW14765H or timed thermostats GW10764H, GW12764H, GW14764H to adjust the temperature in specific areas and for controlling and displaying the probe parameters (the probe does not have a display).
NOTES: it is equipped with coupling terminal for connection to bus.

CHARACTERISTICS: flush-mounting temperature/humidity probe sensor for sending temperature and relative humidity values on the KNX BUS. Temperature range: 0…+45°C. Relative humidity range: 10-95%. Equipped with a front signalling LED. To be configured with ETS software or with Easy Controller.
NOTES: equipped with coupling terminal for connection to BUS.

CHARACTERISTICS: NTC sensor 10K BETA 3435 1%. Temperature range: -50…+110 °C; precision: ±1%; capsule material: thermoplastic rubber.
NOTES: to be used in combination with the EASY and KNX timed thermostats, thermostats, temperature sensors, EASY and KNX flush-mounting humidity/temperature sensors, input modules, etc..

CHARACTERISTICS: NTC flush-mounting temperature probe sensor 10K ±2%, BETA 3977 ±0.75%. Temperature range: -40…+125°C. Equipped with a front signalling LED.
NOTES: to be used in combination with the timed thermostats, thermostats, temperature sensors, EASY and KNX flush-mounting humidity/temperature sensors, input modules, etc..

CHARACTERISTICS: flush-mounting thermostat to control heating/cooling systems on the BUS and manage the temperature in manual mode or on 3 levels (comfort, pre-comfort, economy). Control algorithms for 2- or 4-way systems: two points (ON/OFF or 0%/100%), proportional-integral (PWM or continuous), fan coil (with ON/OFF or proportional-integral valve control). Can be used to manage humidification/dehumidification systems if connected to an external humidity sensor (e.g. GW1x762H). Includes 1 input for a potential-free contact (for the window contact function, or for managing fronts, dimmers, roller shutters and scenes); 1 input for the external temperature NTC probe sensor (e.g. protection for floor-mounting heating) or, alternatively, as a second input for a potential-free contact. With user interface with touch commands (capacitive) on glass plate and backlit display. The thermostat has built-in proximity and temperature sensors. To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with KNX flush-mounting timed thermostats or KNX control panels for local temperature adjustment: In this case, the thermostat acts as the slave by executing the temperature profile sent by the master.
NOTES: equipped with coupling terminal for connection to BUS. The thermostats include a front plate, electronic unit and metal support, and are suitable for screw fixing on both rectangular 3-gang boxes (centre distance 83.5 mm) and round/square boxes (centre distance 60 mm) equipped with fixing columns. Plate material: glass.

APPLICATIONS: to be used for powering LPG detectors (GW10711, GW12711, GW14711, GW20868, GW21868, GW30520), methane detectors (GW10712, GW12712, GW14712, GW20867, GW21867, GW30519); Thermo ICE WiFi (GW16972CB, GW16972CN, GW16972CT) and KNX/Easy (GW16974CB, GW16974CN, GW16974CT) thermostats.

CHARACTERISTICS: timed thermostat that can be programmed on a weekly basis to control heating/cooling systems on the BUS.
3-level temperature profile (comfort, pre-comfort, economy). Regulation with two-point (ON/OFF) or proportional (PWM) control.
Equipped with a backlit LCD display. To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with thermostats GW10763, GW14763 to adjust the temperature in specific areas. In this case, the timed thermostat acts as a master, sending the temperature profile to the BUS.
NOTES: equipped with coupling terminal for connection to BUS. The device requires a back-up power supply from 2 AAA alkaline batteries (not included), to guarantee the updating of the calendar (day, time) in the event of a BUS voltage failure.

CHARACTERISTICS: thermostat to control heating/cooling systems on BUS.
Regulation with two-point (ON/OFF) or proportional (PWM) control. Equipped with a backlit LCD display. To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with timed thermostats GW10761, GW14761 to adjust the temperature in specific areas.
in this case, the thermostat acts as a Slave, executing the temperature profile sent from the Master (timed thermostat), using the locally defined setpoint values. This also makes it possible to control the fan coils.
NOTES: equipped with coupling terminal for connection to BUS.
Equipped with a rechargeable back-up battery to guarantee the updating of the calendar (day, time) in the event of a BUS voltage failure.

CHARACTERISTICS: wall-mounting thermostat to control heating/cooling and humidification/dehumidification systems on the BUS and manage the temperature in manual mode or on 3 levels (comfort, pre-comfort, economy). Control algorithms for 2- or 4-way systems: two points (ON/OFF or 0%/100%), proportional-integral (PWM or continuous), fan coil. Includes 1 input for external NTC temperature sensor (e.g.: protection for flood mounting heating). Equipped with a user interface with touch commands (capacitive) on technopolymer plate and backlit display. The thermostat has built-in proximity, temperature and humidity sensors. Hardware prepared for future implementations (OpenTherm protocol). To be configured with ETS software or with Easy Controller.
APPLICATIONS: can be combined with KNX flush-mounting timed thermostats or KNX control panels for local temperature adjustment: in this case, the thermostat acts as the slave by executing the temperature sent by the master.
NOTES: equipped with coupling terminal for connection to bus. Wall fixing with wall plugs or screw fixing on rectangular 3-gang boxes (centre distance 83.5 mm). Plate material: technopolymer.

APPLICATION: allows the measurement and visualisation on the display of the active energy values (exported and imported), istantaneous active power (exported and imported), voltage, current, power factor and frequency.
If used with the KNX GW90876 interface, the measured values can be sent on the KNX BUS.
If used with the MODBUS GWD6820 interface, the measured values can be sent on Modbus RS485.
CHARACTERISTICS: the energy meters have an impulse output for remote energy consumption control.

APPLICATION: allow the measurement and the visualization on display of the active and reactive energy values (exported and imported), and instantaneous active and reactive power values (exported and imported). If used with the KNX GW90876 interface, the measured values can be sent on the KNX BUS.
If used with the MODBUS GWD6820 interface, the measured values can be sent on Modbus RS485.
CHARACTERISTICS: the meters have two impulse outputs for remote energy consumption control.

CHARACTERISTICS: configurable with EASY controller (the interface is presetted with dedicated group addresses).
APPLICATIONS: it communicates on the KNX bus system the values of energy and power measured by the GWD6801, GWD6802, GWD6806, GWD6807, GWD6808, GWD6809 energy meters. The KNX interface is optically coupled with the energy meter (the two devices have to be installed side-by-side).
NOTE: it is equipped with coupling terminal for connection to bus.

Can be installed with the 230V power supply cable, and are recommended for protruding or flush assembly, for arrangement in conduits, in dry environments, and outdoors if protected against direct solar irradiation.
In the GW90582 KNX cable, the first duplex cable (red + black) is used for the power supply and the data transmission of the KNX devices; the second one (yellow + white) can be used for another SELV service power supply.
In the KNX cable GW90583, the duplex cable (red + black) is used for the power supply and the data transmission of the KNX devices.
CHARACTERISTICS: GW90582 BUS cable for shielded installation consisting of 2 pairs of twisted wires. Colours - black/red + yellow/white.
GW90583 BUS cable for shielded installation consisting of 1 pair of twisted wires. Colours - black/red.

APPLICATIONS: for connecting up to 4 pairs of conductors. Can also be used as a junction terminal.

APPLICATIONS: for connecting up to 4 pairs of conductors. Can also be used as a junction terminal.